Getting Your SIPA SFR 12 Heating Lamps Right Keeping a SIPA SFR 12 rotary blower running smoothly usually comes down to one thing: the heat. If your...

Getting the Heat Right on the KOSME KSB 4000/6000 If you’re running a Husky HyPET high-speed system, you know the struggle. The biggest...

Better IR Lamps for Your Krones and Sidel Blow Molders If you’re running PET stretch blow molding, you know the drill. You need the preforms...

Stop Overpaying for Krones Contiform IR Lamps Let’s be honest: OEM parts for Krones Contiform machines are expensive. Really expensive. It...

Getting the Heat Right for Husky HyPET Systems When you’re running high-speed PET blowing, just cranking up the heat isn’t enough. If the...

Getting the Heat Where it Actually Matters in Husky HyPET Systems If you’ve spent any time with high-speed PET blowing, you know the headache...

Getting Your SACMI Blow Molders Up to Speed If you’re running SACMI rotary machines, you know they move fast. Like, really fast. In that kind...

Getting Your Sidel Matrix Heating Just Right If you’re trying to match the heating curve of an OEM Sidel Matrix lamp, you already know it’s not...

Getting More Life Out of Your SIG Blomax 4/6/8 If you’re running an older Blomax 4, 6, or 8, you probably know the struggle. Over time, those heating...

Stop Replacing Your SIG Blomax Lamps Every Two Weeks If you’re constantly swapping out heating lamps on your SIG Blomax line, you know how...

Keeping your Nissei or Krones running without breaking the bank If you’re running a Nissei ASB 70DP or a Krones Contiform, you already know the...

Getting Your Sidel Matrix Heating Just Right Here is the problem when you swap out original lamps for third-party ones in a Sidel Matrix blower: the...

Stop the Burnout Cycle on Your SIG Blomax Lines If you’re running SIG Blomax lines, you know the headache of heating lamps blowing out. It...

Stop Fighting Your SIPA Oven’s Heat Ever notice how a few mismatched IR lamps can mess up your entire run? It happens all the time. You’ve got...

Getting the Heat Right in Your Husky HyPET System If you’ve ever pulled a bottle off the line and seen those annoying thin spots or that weird,...

Getting Your IR Lamps Up to Speed on SACMI Rotary Machines When you’re running SACMI rotary blow molding machines, everything happens fast....

Can New IR Heaters Actually Speed Up Your Old Blow Molding Machine? Let’s be honest: most shop floors are running older blow molding machines that...

Stop the Blow-outs: Getting Your Sidel SBO Series 2 Heating Right If you’re running a SIG Blomax line and your tubes keep blowing out, you...

Getting Your Rotary Blow Molding Up to Speed If you’re running high-speed machines like the SIG Blomax 6 or the SACMI series, you know the...

If you’re running SIG Blomax machines, you know the headache of lamps blowing out. One minute you’re cruising, the next you’ve got...

Getting Your Heat Back to Normal with Sidel Matrix Lamps Here is the problem with replacing infrared lamps in a Sidel Matrix oven: the temperature...

Introduction We built these replacement heating lamps for one reason: to give your Husky HyPET system the heat it’s been missing. The whole...

Introduction We built the Sidel SBO 16 Series 2 heater lamp bulb to be a straight-up, no-fuss replacement for the original. It’s a shortwave...

Introduction We built the Nissel ASB heating lamp for one reason: to fit Sidel PET stretch blow molding lines like a glove. It drops straight in,...

The Sacmi Lamp: Built for the Heat of the Factory Floor Let’s cut to the chase. We built the Sacmi blowing machine lamp for one reason: the...

Introduction Ever feel like you’re stuck in a rut on the shop floor? You’ve got this older PET blowing machine—solid, dependable—but it...

On the blow molding floor, uneven preform heating is the kind of problem that quietly bleeds you—cycle time disappears, scrap climbs, and bottle...

On the blow molding floor, the heating tunnel is where you either keep running or start scrambling. When an infrared lamp starts to drift, preforms...

On the floor, the Combi SF300 keeps a tight rhythm. When the heating tunnel starts drifting, preforms come out uneven, and the blow molder starts...

On a blow molding line, heating isn’t a background step. It sets the cycle, drives wall distribution, and determines whether you ship good bottles or...

On an SMI blow molding line, the heating tunnel is where the whole cycle hangs together. Once the original lamps start drifting off-spec, you’ll see...

On the floor, the SIPA SFL needs to run steady—no excuses. When preform heating starts drifting, you’re staring down thin shoulders, blown seams, and...

On a Husky stretch blow molding line, the heating tunnel is where the run either makes sense or starts to fall apart. If the preform temperature...

On a rotary blow molding line, heating drift will throw your whole cycle off. Preforms come out uneven, scrap climbs, and you end up chasing...